簡介General Description
此液壓動力單元由高齒輪油泵、直流電機、多用集成塊、
液壓閥、油箱等零部件有機結合為一體，廣泛應用于堆高車、
升降平臺、電磁卸荷閥卸荷實現回油，下降速度由可調節流閥
控制，備用手動卸荷閥用于停電時下降。
Consisting of high pressure gear pump,DC motor, multi-functional
manifold,valves and tank,this power unit has been widely used in the
industry of logistic devices such as fork lift,mini lift table and scissors
lift.The lowering movement is controlled by the solenoid valve with the
lower speed controlled by adjustable throttle valve.The needle release
valve is used for lowering movement in case of power failure.
型號規格說明Model Specifications
| 型號Model | 電機電壓Motor Volt | 電機功率Motor power | 名義轉速Rated Speed | 油泵排量Displacement | 溢流閥壓力System pressure | 油箱容量Tank Capacity | L(mm) |
| JBZ-F1.2A1W2/WUAAG1 | 12VDC | 1.5KW | 2500RPM | 1.2mL/r | 20MPa | 3.5L | 409 |
| JBZ-F1.6B1W2/WUAAG1 | 1.6mL/r | 5L | 459 |
| JBZ-F2.1B1W2/WUAAG1 | 2.1mL/r | 5L | 459 |
| JBZ-F2.1B2A2/WUABG1 | 24VDC | 2KW | 2.1mL/r | 6L | 509 |
| JBZ-F2.5C2A2/WUABG1 | 2.5mL/r | 8L | 579 |
| JBZ-F2.7C2A2/WUABG1 | 2.7mL/r | 8L | 579 |
說明Remark::
1.如需不同流量的泵、壓力、電機功率等系統參數，請查看液壓動力單元型號說明。
Please go to page 1 or consult our sales engineer for the different pump displacement,motor power or tank capacity.
2.如需手動應急放油裝置，請在訂貨時說明。
The manual override function is available on request.
注意事項Special Notes
1.本動力單元為S3工作制，不可連續運轉，30秒開，270秒停。
1.The duty of this power unit is S3,i.e.,30 seconds on and 270 seconds off.
2.安裝前必須保證油缸、油管、接頭等液壓元件清潔無任何雜質粘附。
2．Clean all the hydraulic parts concemed before mounting the power unit.
3.液壓油粘度應為15-68CST，應清潔無雜質，推薦使用N46號液壓油。
3.The viscosity of the oil shoud be 15-68 cst.
4.系統使用第一個100小時后，應更換液壓油，以后每3000小時更換一次液壓油。
4.Change the oil after the first 100 hours of using the power unit,then change the oil every 3000 hours
5.本液壓動力單元適用于水平安裝。
5.The power unit should be mounted horizontally.